Cypress Semiconductor FX2LP Przewodnik Instalacji Strona 1

• Cypress Semiconductor • Personal Communications Division • • 15050 Avenue of Science • Suite 200 • San Diego, CA 92128 •EZ-USBGetting StartedDevelop

EZ-USB Development Kit Manual - Getting StartedPage -6 EZ-USB Development Kit Manual - Getting Started Rev 1.0 4.0 EZ-USB Advanced Development Board

EZ-USB Development Board Page -74.3 Jumpers 4.4 EEPROM Select & Enable Switches SW1 and SW2SW1 selects between two socketed EEPROMS, one strappe

EZ-USB Development Kit Manual - Getting StartedPage -8 EZ-USB Development Kit Manual - Getting Started Rev 1.0 “Small” EEPROMS are typically used to s

EZ-USB Development Board Page -93. ‘C2 Load’: SW2=ON, SW1=LARGEA “C2” load provides a method for loading the EZ-USB internal RAM with 8051 firmware b

EZ-USB Development Kit Manual - Getting StartedPage -10 EZ-USB Development Kit Manual - Getting Started Rev 1.0 • High speed EZ-USB strobe signals (P

EZ-USB Development Board Page -11Table 6. AlternateDefault P3 Default AlternateN.C. 1 2 3.3VWR#3 4RDY5RDY4 5 6 RDY3RDY2 7 8 BKPTRESET# 9 10 N.C.N.C. 1

EZ-USB Development Kit Manual - Getting StartedPage -12 EZ-USB Development Kit Manual - Getting Started Rev 1.0 4.6 ATA Connector P8 Table 10 shows t

EZ-USB Development Board Page -134.7 U2 -- 22v10 GALA standard 22v10 GAL provides general purpose “glue logic” on the board. It provides the AND gate

EZ-USB Development Kit Manual - Getting StartedPage -14 EZ-USB Development Kit Manual - Getting Started Rev 1.0 – The third column, “Ext Flash”, allow

EZ-USB Development Board Page -15U9 has the group address 0100, and is strapped to unit address 000. Therefore to read the switch values, 8051 firmwa

Cypress Disclaimer AgreementThe information in this document is subject to change without notice and should not be con-strued as a commitment by Cypre

EZ-USB Development Kit Manual - Getting StartedPage -16 EZ-USB Development Kit Manual - Getting Started Rev 1.0 The low address byte is “don’t care”.

EZ-USB Development Board Page -175.0 Frequently Asked QuestionsQ1: What should I do first (after viewing the printed material from the box)?A1: Make

EZ-USB Development Kit Manual - Getting StartedPage -18 EZ-USB Development Kit Manual - Getting Started Rev 1.0 Q10: Where can I get a summary of the

EZ-USB Development Board Page -196.0 Appendix A: U2 (GAL) code (file is 'FX2LP.ABL')MODULE fx2lp" Swapped dipswitch settings 00 and 1

EZ-USB Development Kit Manual - Getting StartedPage -20 EZ-USB Development Kit Manual - Getting Started Rev 1.0 !nRAMOE= !nRD # !nPSEN;EA = 0;}ELSE WH

EZ-USB Development Board Page -21Figure 1-2. CY3684 Assembly Development Board Layout

EZ-USB Development Kit Manual - Getting StartedPage -22 EZ-USB Development Kit Manual - Getting Started Rev 1.0 The schematic for the CY3684 appears o

5544332211D DC CB BA A128K x 8 SRAMPLACE ONE CAP PER EACH VCC PIN ON U1REDBridge SP1-SP3 for Atapi use.RED8-PIN DIP SOCKETSMALL EEPROMLARGE EEPROMNO E

EZ-USB Development Kit Manual - Getting StartedPage -24 EZ-USB Development Kit Manual - Getting Started Rev 1.0

iTable of ContentsEZ-USB Development Kit Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Intr

ii Table of Contents

EZ-USB Development Board Page -1Getting Started1.0 EZ-USB Development Kit Overview1.1 IntroductionThe EZ-USB Development Kit (DVK) is the best star

EZ-USB Development Kit Manual - Getting StartedPage -2 EZ-USB Development Kit Manual - Getting Started Rev 1.0 • Cypress USB Console• Cypress GPIF Des

EZ-USB Development Board Page -32.2 Compatibility with Earlier EZ-USB Development KitsThis EZ-USB Advanced DVK has the ability to co-exist with older

EZ-USB Development Kit Manual - Getting StartedPage -4 EZ-USB Development Kit Manual - Getting Started Rev 1.0 • Windows 98 and 98SE – For PCI add-in

EZ-USB Development Board Page -53.1 Confirm Successful Installation using the Cypress USB ConsoleRun the Cypress USB Console application and perform